Investing in quality, comfortable furniture is one of the best things you can do with your money. Whether you are buying furniture for your home or your RV, it’s essential to find couches and recliners that you can rest in and enjoy.
When it comes to buying a new recliner, there are many options available to you. Most chairs will look similar and have a lot of the same features, so it can be difficult to tell which is superior.
Flexsteel power recliners are one of the most popular recliners out there in the RV world, but what problems can you face with them?
1. Electrical Issues
Problems with electricity are common among owners of Flexsteel power recliners. The problem often starts when you notice the recliner is no longer functioning. That can be caused by the outlet the recliner is plugged into. If that is the case, the outlet may be faulty, and you will have to replace it. Some technical issues can cause you to have problems.
However, it is best to start troubleshooting by checking your outlets first then move on to possible technical issues.
To test your electrical sockets, remove the main plug and use a voltmeter to check the connection. If there are no issues with the current, you can continue to the next step. However, if you notice any fluctuations or no current incoming, the socket should be replaced.
Another way to check your outlets if you don’t have a voltmeter is to plug another device into them, such as a lamp. Using a lamp is ideal because you can notice if the bulb is lighting up correctly or not. If the bulb is flickering or flashing, your socket may be going bad.
Before installing a new electrical outlet, be sure to check the current rating.
You should also consider purchasing a surge protector, which can help protect your outlets from damage. A surge protector will keep your outlet protected even when the current value starts to fluctuate.
2. Stops Working
Flexsteel recliners have cords throughout their system that help control the electrical features. You should keep in mind that any type of movement or even sitting in your recliner can cause the cord connections to loosen.
There are two main wires, out of them one provides the current directly from the outlet which is transported to the motor using the second wire. If the connection between these two wires is cut off, the recliner will stop working.
That can happen quite often, and there is usually no need to panic since you can simply flip over the recliner to access the wires and reconnect them.
Locating the wires can sometimes be difficult, and you may need to use a flashlight to help you find them. Once you find the wires you can trace them to find where they became disconnected. You can easily attach the wires back together and ensure they are connected securely.
If there are no further issues, your recliner should start working normally again.
If you are having difficulty finding the wires, you should keep in mind that there are several different models of Flexsteel recliners, and the wiring may vary from one model to the next. You should refer to your owner’s manual for assistance or consult with a dealer if you need assistance. You may be able to download a copy of the owner’s manual online by searching using your recliner’s model number.
3. Needs to Be Reset
If you still have an issue with your Flexsteel recliner, you could have a problem with the board being burnt out. If that is the problem, you will need to get in contact with Flexsteel and let them know about the issue. They will provide you with a solution, and if your recliner is still under warranty, you can file a claim.
Before you contact Flexsteel however, you can try resetting the recliner to see if that fixes the problem. Sometimes there are errors with the configuration that can cause the recliner to stop working.
This can happen when you change the settings, and the system doesn’t fully recognize them. By resetting the device, it will put the recliner back to factory settings.
To reset your Flexsteel recliner, check the open and close buttons and look for a pinhole. It should be labelled as reset. Hold the pin inside for a few minutes and then release to see if that corrects the problem You can also try a hard reset. This involves disconnecting the recliner from the main power source for at least two minutes. After that, you need to plug the recliner back into the outlet to reset it.
4. Locks in Reclined Position
Some users have reported their recliner locking in the recline position. While all the connections on the chair are fine and overall, the chair seems to be fine, it remains in the same position and will not go upright. Many times, this will be caused by the wires becoming disconnected. To solve this issue, you should inspect the wires and make sure they are all connected securely.
If that doesn’t solve the problem, try doing a hard reset. Some users have stated that extending the footrest of the recliner out to its maximum height or continuously pressing buttons can cause the motor’s current to spike, and that causes the breaker to trip.
The breaker is located in the recliner’s battery compartment. There you can check the status of the breaker and any fuses that are located there also. If nothing else works you will need to consult with the dealer for assistance.
Flexsteel has been around for several years and is considered a reliable company by many RV owners. Their recliners are high-quality, comfortable seats to add to your RV and they are designed to be long-lasting.
They are considered to be a worthwhile investment and the minimal issues discussed here can be resolved without spending much time or effort on them. If you are considering upgrading your recreational vehicle, you should think about adding one or more Flexsteel recliners to your RV and making your future road trips or camping trips much more enjoyable.